Posts

Seagate Hard Drive Firmware Repair Tool Datasheet 2024

,

Seagate hard drive firmware repair tool-DFL-Seagate
Section 1: HDD Working Modes
Engineer can work in both ATA and COM terminal mode to diagnose and repair the HDD.

Section 2: Repair Modes

DFL Seagate firmware repair tool can do both hdd repair and hdd refurbishing, hdd repair is to fix firmware failures without affecting data but hdd refurbishing will remove bad sectors and destroy data.

Section 3: Number of HDD Supported by the DFL Seagate Hardware

Users can connect 3 drives to SRP portable Seagate hdd repair tool and 4 drives to PCIe Seagate hdd repair tool.

Section 4: Operating System to Install the software

Win 7, Win 8, Win 10, any of them is ok. DFL tools have unique driverless technology, no need to install device drivers.

Section 5: Biggest Advantages over Competitors

Easy to use and install on any pc, powerful with best technique support and data recovery resources.
Free data recovery training videos here: https://www.youtube.com/user/datarecoverytools

Section 6: What Kind of Seagate HDD Failures DFL Seagate can Fix

01: Seagate HDDs with many bad sectors;
02: Seagate HDDs with SA locked;
03: Seagate HDDs with ATA locked;
04: Wrongly detected Seagate hard drives;
05: 0 capacity detected Seagate hard drives;
06: Undetected/Busy Seagate hard drives;
07: Dead Seagate hard drives, to fix this kind of dead Seagate drives, users need to have ROM chip reader, donor PCB sources or physical head and platter swap tools to work with DFL Seagate firmware repair tool;
08: Seagate patient HDDs with LED status;
09: Seagate patient HDDs with weak heads;

Section 7: Common Seagate HDD Firmware Failures-Quick Fix

01: Busy fix;
02: Capacity 0 fix;
03: Ready then Busy Fix;
04: DWF fix;
05: Sim 1002 fix;
06: Sim 1009 fix;
07: MCMT corruption fix;
08: Dos fix;
09: SMART fix;
10: LED fix;
11: Partial sector access fix;
12: Clear NG;
13: Remove password;
14: SMR HDD Format fix;
15: SSHD non-spin fix;
16: Clear media cache;
17: Load ATA/APP for old Seagate drive(Barracuda 7200.7-.10);
18: CELOG fix;
etc

Section 8: ROM Operations-Firmware on PCB

01: Read ROM by ATA or COM;
02: Write ROM by COM at any defined baud rates;
03: Head adaptive ROM;
04: CC49 ROM;
05: Edit head map in ROM;
06: Terminal/firmware unlock by generating and writing unlock rom;
07: Edit ROM;
08, Cut head in ROM;
09, Adjust Heads’ Working Temperature;
10, Disable Subsystem to fix LED issue;
11, Change ROM modules, write key original rom modules to donor ROM;
12: Nohost fix ROM generation;

Section 9: Service Area Operations-Firmware on Platters

01: Read/write firmware modules;
02: Read/write tracks;
03: Read/write/Edit SYS files;
04: Repair unknown firmware failures by tracks;
05: Repair unknown firmware failures by ABA;
06: Read/Write LOD;
07: Read/write SA;
08: Scan and record bad sector locations and add bad sectors to P-list;
09: Edit HDD ID (Model number/ LBA /SN number) and remove password;
10: Test SYS files;

Section 10: Service Area in RAM

01: Edit head map in RAM;
02: Load ATA in RAM;
03: Edit ID in RAM;
04: SAP Control flag;
05: Load translator to RAM;
06: Load ROM to RAM (for hot swap purpose);

Section 11: Defects Operations

01: Read/write/Edit G-list, P-list, NG list, Smart;
02: Delete non-SF defects in P-list, very helpful for fixing some sector access problems;
03: Delete specific defects on specific heads, this is usually used to cut heads for hdd refurbishing purpose;
04, Translator Clear and regeneration;
05: Translator Auto fix;
06, Format with Glist/Plist;
07: Offline bad sector repair;

/0 Comments/by

Western Digital Hikvision DVR SMR Hard Drive Data Recovery Solution

,

With DFL-WD hard drive firmware repair tool, users can easily recover the lost data from Western Digital Hikvision DVR password protected hard drives.

The patient hard drive in this article was one Western Digital SMR hard drive, 2TB, PCB-810011.

When users connect the patient hard drives to computers or data recovery hardware, the data area was not accessible, the firmware area was locked too.

To recover the lost data from the Western Digital Hikvision DVR hard drive, users need to remove the firmware lock by DFL-WD hdd firmware repair tool and then within the WD hdd firmware repair software, there’s one function to remove the dvr password for this patient hard drive.

After fixing the DVR password protection issue, users can make best use of the original PCB to recover the lost data by DFL-DDP data recovery equipment.

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

Seagate ST1000DM010 Pharaoh Oasis FamilyId 94 HDD Firmware Repair and Data Recovery Steps

,

This is one successful Seagate ST1000DM010 Pharaoh Oasis FamilyId 94 HDD Firmware Repair and Data Recovery case study.

HDD Failure Symptoms:
Fail to access firmware area, Partial Sector Access

Pharaoh Oasis LuxorLite 1.0, 1MB Flash, ABIE, PBASeed, SP2.5, DFﾔZN1MB3NK
Product FamilyId: 94, MemberId: 06
HDA SN: ZN1MB3NK, RPM: 7197, Wedges: 188, Heads: 2, OrigHeads: 2, Lbas: 00000E8FEAA6, PreampType: B0 D4
Bits/Symbol: C, Symbols/UserSector: BEB, Symbols/SystemSector: 1A5
PCBA SN: 0000M125B0JJ, Controller: LUXORLPLUS_2_0(0205), Channel: STX_DUNRAVEN, PowerAsic: Unknown Rev 00, BufferBytes: 4000000
SF ID: 0 0, SF Part Size: 400, Flash Used: 400
Package Version: PAA5010B4.CCD4.PH021C.CC43 , Package P/N: 100792845, Package Global ID: 00496476,
Package Build Date: 12/03/2015, Package Build Time: 11:20:16, Package CFW Version: PAA5010B4.CCD4.PH021C.00969095.00496476.CC43 ,
Package SFW1 Version: B423, Package SFW2 Version: —-, Package SFW3 Version: —-, Package SFW4 Version: —-
Controller FW Rev: 12031120, CustomerRel: CC43, Changelist: 00969095, ProdType: PAA5010.CCD4QC, Date: 12/03/2015, Time: 112016, UserId: 00496476
Servo FW Rev: B423
TCG IV Version: n/a
Package BPN: 36
RAP FW Implementation Key: 16, Format Rev: 0005, Contents Rev: 0B 01 00 00
Active BFW Container: 0
4K Sys Area: 0
Features:
– Quadradic Equation AFH enabled
– VBAR with adjustable zone boundaries enabled
– Volume Based Sparing enabled
– IOEDC enabled
– IOECC enabled
– DERP Read Retries enabled v. 4.7.01.0000000000000013
– LTTC-UDR2 disabled
– SuperParity 2.5 enabled
– Humidity Sensor disabled
– Media Cache Partition enabled
– Background Reli Activity Critical Event Logging disabled
– Torn Write Protection disabled
– SubRelease:0
– DRAM Mirror disabled

HDD Repair Tools and Data Recovery Tools Required:

DFL Seagate HDD Firmware Repair Tool
DFL-DDP Data Recovery Equipment

HDD Firmware Repair Steps and Data Recovery Steps:

Unlock firmware area and enter F3 T>;
Backup important sys files;
Clear glist;
Clear nglist;
Regenerate translator;
Open DFL-DDP data recovery software and all lost partitions are available for immediate data recovery.

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

MQ01ABD075H MQ02ABF050H MQ02ABD100H Toshiba SSHD Data Recovery Steps

,

MQ02ABF050H MQ02ABD100H Toshiba SSHD data recovery cases are common in many data recovery labs worldwide.

When users receive the MQ02ABF050H MQ02ABD100H Toshiba SSHDs or similar ones, users try to access the data area but failed. If running logical scan, users may get full disk bad sectors.

To fix above Toshiba SSHD failures, users need to enter the DFL Toshiba HDD firmware repair software, menu path: Firmware Operations>Change Disk Configuration>Turn Off Flash Permanent Cache.

Next users just need to click Tech Off mode and users can run logical scan successfully and access to data area.

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

WD5000AAKS Head Damage HDD Repair and Data Recovery Steps

,

This is one successful Western Digital hard drive data recovery case study shared by one DFL user in India. The patient drive had head failure, kept busy and had no access to data area at all.

Patient HDD ID:

Model-WD5000AAKS
PCB: 1640 series

To recover lost data from head damaged hard drives, the very first step is to find one donor hdd with donor heads, users usually check the model and pcb number and sometimes, the DCM is to be checked as well.

After finding the donor hdd, users need to open the patient drive in clean room environment and swap the heads.

Next users need to enter the DFL WD hdd firmware repair software and backup the rom and important firmware modules including the 03, loaders, 31, 36, 40, 49, 4A.

Next users can test the firmware modules and find out which modules are damaged and then repair the damaged firmware modules. In most wd traditional hard drives, we need to run the slow fix.

Next we can use DFL-DDP data recovery software to set up disk image project, set up head map, image good heads and then weak heads.

Finally we can extract lost data from the image file or target drive.

Head Replacement Tools, HDD Repair Tools, Data Recovery Equipment required in above case study:

Hard Drive Ramp Toolkit Pro.
DFL-WD hdd firmware repair tool
DFL-DDP Data recovery tool

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

SIM FileFD FC00320D ErrorCode 43160080 Remaining in BootFW

,

This is one data recovery case from one DFL user in Indonesia and it’s actually one Seagate physical hdd firmware repair and data recovery cases.

HDD ID:
Model : ST1000LM035-1RK172
Serial : WKP4P877
Firmware : EB01
Capacity : 281474976710655 (134217728.00GB)
Obtain failed
Sector size : 512
Heads number : Obtain failed

COM Terminal Output Messages:

Bootﾠ0x80M
TCC:002B
[LBA=0x00000001][LBA=0x00000001]
ﾠRECOVﾠServoﾠOp=06DFﾠResp=0005

DSC PASS
ﾠRECOVﾠServoﾠOp=0095ﾠResp=0005

ﾠSIMﾠFileFD=FC000000ﾠErrorCode=43160080ﾠDiscLBA=0000000000000001ﾠDuration=00000649ﾠms
ﾠRECOVﾠServoﾠOp=0195ﾠResp=0005[LBA=0x0000DA01][LBA=0x0000DA01]

ﾠSIMﾠFileFD=FC000000ﾠErrorCode=43160080ﾠDiscLBA=000000000000DA01ﾠDuration=00000048ﾠms
ﾠRECOVﾠServoﾠOp=0095ﾠResp=0005[LBA=0x00000406][LBA=0x00000406]

ﾠSIMﾠFileFD=FC00320DﾠErrorCode=43160080ﾠDiscLBA=0000000000000406ﾠDuration=00000047ﾠms
ﾠRECOVﾠServoﾠOp=0195ﾠResp=0005[LBA=0x0000DE06][LBA=0x0000DE06]

ﾠSIMﾠFileFD=FC00320DﾠErrorCode=43160080ﾠDiscLBA=000000000000DE06ﾠDuration=00000046ﾠms

SimErrorﾠ-ﾠRemainingﾠinﾠBootFW

Performﾠaﾠdoubleﾠdownloadﾠwithoutﾠaﾠpowerﾠcycle

Above hdd failure was caused by head corruption and the user swapped the heads and finally got all lost data back with DFL-DDP data recovery tool.

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

Alat Perbaikan Firmware HDD Seagate dan WD

Perkenalkan saya Suryanto dari Perusahaan Data Recovery di Indonesia. Alat manakah yang dapat memperbaiki Firmware pada Harddisk Seagate dan WD.

Alat Perbaikan Firmware HDD Seagate
Alat Perbaikan Firmware WD HDD

Bisakah Anda memberikan penawaran harga spesial untuk kami.

Terima kasih

/0 Comments/by

Data Recovery Solutions for Seagate HDDs with Head Failure

, ,

From this article, users can learn about the firmware repair and data recovery solutions of DFL-SRP USB3.0 all in one data recovery equipment to fix Seagate head-damaged hard drives.

Seagate HDD Head failure means the patient drive has something wrong on the hard drive read or write heads and therefore the data area could not be accessed normally.

Head failure can be weak head, single head damage, multiple heads damage or total heads damage. To fix these hdd head failure, users get the following data recovery solutions from Dolphin data recovery hardware tools:

01: Test heads within COM terminal;
02: Edit head map in the ROM;
03: Edit head map in the RAM;
04: Adjust head flying height/head working temperature;
05: Hot swap to access firmware area;
06: Head map setup for imaging good heads first and then imaging weak heads;

All above functions for fixing Seagate hdd failure are available within DFL Seagate hdd firmware repair tool.

07: Seagate head replacement tools and Seagate SLIM hdd head replacement tool for Seagate hdd head swap in clean room;

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by

Seagate HDD LED Fix New Data Recovery Solution

,

Dolphin Data Lab has created one new Seagate hdd firmware repair function specially for fixing Seagate faulty hard drives with LED status.

For Seagate patient hard drives, users cannot enter F3 T> and cannot do anything further to repair the corrupted firmware modules if the hdd suffers LED failure. It is something like the bluescreen of the computers.

To fix the Seagate LED HDD, there’re several methods:

01: Short connect;
02: Hot swap;
03: Boot ROM write+Loader

Now we create the 4th new and easier method: Disable Subsystem of the SA and this is something like the ‘disable 411’ within WD hard drive firmware repair software, very easy to use and very helpful in many Seagate LED cases.

Users can open DFL Seagate HDD repair tool, enter the software, select ROM Operations>ROM Edit>Disable Subsystem

Next users just need to write new rom to HDD and then users can bypass the LED status, go to COM terminal and enter F3 T>, finally users need to write back the original rom after firmware repair.

Next users can open DFL-DDP data recovery software and get all the lost data back easily.

Any question is welcome to [email protected] or add Dolphin skype ID: dolphin.data.lab

/0 Comments/by

WD SMR HDD Module 190 Auto Repair Solution

,

Dolphin Data Lab has released the latest WD SMR HDD Module 190 Auto Repair Solution within the DFL-DDP data recovery tool.

According to the feedback of Dolphin users and data recovery engineers worldwide, Western Digital hard drive data recovery cases are mostly associated with the dynamic secondary translator-module 190.

Module 190 corruption can be caused by unstable faulty hard drive status: many bad sectors, weak heads, wrong operations by users, etc.

Whenever users get one WD SMR HDD data recovery case, users need to diagnose the patient hdd correctly to find out if it is firmware issue or physical issue, if physical issue, users need to swap heads first or take other measures to fix the physical issue and then users need to manage to remove the MCU lock.

After removing the MCU lock, users need to follow Dolphin special WD SMR hdd recovery instructions to backup the module 190 (even if the module 190 has many read errors, users need to be patient with module reading) and sometimes, users can select to read valid data only from the module 190 and this can avoid many read errors but this may cause some data loss sometimes.

After the module 190 backup, users need to diagnose the module 190 and try to repair the module 190 corruption. Dolphin Data Lab has released one auto repair solution for the corrupted module 190. Users can check the video demo here to find out how the module 190 auto repair works:

Above new WD SMR hdd firmware repair solution helps users a lot to enhance the efficiency and success rate. Users can download it from the Dolphin user-only forum.

Any question is welcome to [email protected] or add Dolphin Skype ID: dolphin.data.lab

/0 Comments/by